|
|
| SHOCKER SPORT USED PARTS |
|
| Used parts mainpage
Shocker Sport parts Impulse parts Shocker SFT parts Nerve parts AKALMP parts Automag parts Ion parts Intimidator parts Regulator, ASA, and Max-Flo parts Barrels |
2000 right feed body - This is used but functional. It has been drilled for 3mm anti-chop eyes and cover screw holes (I didn't do the milling; don't know who did). The body includes the body plugs, Shocker jewel, and brass fire piston ring.
2000 right feed body - Used but functional. This body was modified for a recessed rear macroline fitting, which is included. I don't know who did the modification. The body includes the body plugs, brass fire piston ring, feedtube, and front set screw installed.
2000 powerfeed body - Used but functional. Comes with powerfeed attachment and powerfeed plug installed, rear macroline fitting, Turbo jewel, body plugs, and brass fire piston ring installed.
2002 right feed body - Used but functional. This body was made in early 2002; I used it on one of my markers but took it off when I acquired a vertical feed body. It comes with the RF attachment, body plugs, and brass fire piston ring installed. (no manifold plugs or macroline).
Fire mode switch cover - Bolt onto the front of the circuit housing, to protect the fire mode switch. This isn't tournament lock version, so you'll still be able to adjust the mode through the bottom.
Bolt piston housing only - Housing for the bolt section, comes with new o-rings, but no bumpers.
Bolt piston endcap - Endcap/guide for the bolt piston housing. These are older versions with flathead screwdriver removal.
Bolt piston rod - Comes with new o-rings installed, but no bumpers. Be sure to grease the seals up with a thick coat before installing. These are series 2000 piston rod with flathead screwdriver removal.
Bolt tip - Aluminum bolt tip, series 2000 or 2001 (same performance). It comes with new o-rings installed, but not bumpers.
Bolt piston (complete) - Complete bolt piston with all o-rings and bumpers, fully-greased and ready to go. Includes an aluminum bolt tip (that's all I have available).
Replacement bumpers - These are used on the bolt piston. The large one goes between the bolt tip and the front of the housing; the small one goes in front of the head of the piston ram, inside the piston housing.
Fill poppet - 1999 series poppet, perfectly functional.
Poppet bushing - 1999 series poppet bushing, perfectly functional. Comes with the o-ring (not pictured)
Fill poppet rod
DS 4x4 board for $30. Add a 9v mod for $3, and/or a select-fire switch for $10, and/or a leverswitch mod for $10.
LS 4x4 board for $35. Add a 9v mod for $3.
DS 4x4 board with a 9v mod for $33. Add a select-fire switch for $10, and/or a leverswitch mod for $10.
DS 4x4 board for $30. Add a 9v mod for $3, select-fire switch for $10, and/or a leverswitch mod for $10.
Circuit housing - This housing was stripped on the outside and buffed so it will be silver instead of black. It is otherwise stock, with the solenoid pads installed.
Gadget grip - Replaces your front frame screw. This includes the barrel plug and threaded stud needed for assembly. It's in perfect condition, there's virtually no wear to the outside.
Stock LS double trigger silver (this is series 2002)
Stock LS double trigger black (this is series 2000).
Stock DS single trigger (silver)
Modified double trigger frame (black) - Stock frame from a 1999 Shocker, modified for a double trigger. Comes with no hardware.
Single trigger frame (black) - Stock single trigger frame from a 1998 Shocker; comes with no hardware. Trigger guard was cut so it'll accept double triggers if you want.
Double trigger frame (silver) - Stock double trigger frame from a 2000 Shocker.
Navigation:
|
