General disassembly and tune-up:
This is the standard fee for any shooting/leaking problems, and can also be added onto other repairs if the marker needs a good cleaning and regreasing. Any shooting/leaking problems will require this fee as a minimum (labor charge). The general tune-up includes the following tasks:
· Service for the marker and regulator; the solenoid will be cleaned only if necessary to remedy a problem.
· Removal and cleaning of the hammer/valve piston, basic cleaning for the LPR and vertical regulator, cleaning the bolt and Nerve body bores for obvious dirt or other debris.
· Includes the labor charge for repairing leaking/shooting problems.
· Replacment of any damaged or worn o-rings. Replacing bumpers is included if needed.
· Adjusting dwell to an optimal level.
· Cost for replacement parts, should you need them, is not included. There may be added charges to remedy some problems you may be experiencing, depending on the issue (I would quote you before installing the part). Contact for a specific quote.
General tune-up costs $15 for the Nerve.
Complete disassembly and rebuild:
This is an upgraded service from the "general" tune-up. The complete disassembly and rebuild is most often used for newly-purchased used markers, or alternately for markers that are about to be sold or traded off (which will hopefully add to the selling price). This service involves the following:
· Service for the marker, regulator(s), and solenoid. You can send in multiple vertical regulators if you have backups.
· Complete disassembly of all pneumatic components; thorough cleaning to remove all accessible debris, moisture, or grease. The solenoid insert, vertical adapter, and solenoid manifold are all disassembled and cleaned.
· Complete rebuild of all standard o-rings and bumpers on the entire marker, regulators, and solenoid manifold. Solenoid internal seals aren't included.
· Rebuilding the solenoid insert is performed if necessary.
· Includes the labor charge for repairing leaking/shooting problems as well.
· Adjustment of dwell and all other electronic settings to their optimal levels (any board).
· Cost for replacement parts, should you need them, is not included. There may be added charges to remedy some problems you may be experiencing, depending on the issue. Contact me for a specific quote.
· This service requires approximately 30-50 minutes plus one additional overnight session of downtime. The marker reassembly requires allowing loctite seals to cure overnight so this service takes longer than usual.
Complete disassembly/rebuild costs $25 for the Nerve.
Electronics repair:
· Battery connector repair ($5) - This is the general price for 9v battery connector-related problems. This incluses reattaching wires to the mainboard, splicing a broken or cut wire, or replacing the battery snap itself.
· Trigger microswitch repair ($12) - Replacement of a broken trigger microswitch. Please specify either a 25 gram (stock) or slightly heavier 80 gram switch when you send the board in. This repair applies to all available boards.
· Circuit (IC) component repair ($10-15) - This is the cost to replace a broken circuit component on the circuit board. This could be a resistor, diode, transistor, or some other part. These problems are uncommon, but not completely unheard-of. The cost is $10 for most repairs however parts that must first be special-ordered cost an additional $5 (contact for details).
· Upper board grip screw damage repair ($15) - This is the cost for repairing damage from screwing the grip panel screws in too far. The board can always be repaired; however the solenoid may have been damaged when the board was impacted. Solenoid damage is rare, however can still occur. I will let you know if this is the case with your board/solenoid. Shown below is a severely damaged board. Shorter grip screws are also available at $0.75 each.
· Power/dwell button repair ($10) - This is the cost for repairing the actual button on the surface of the circuit board. If the switch fell apart or completely broke off, this is what you need. This isn't a repair for the clear actuator in the frame (if it's broken then it would need to be replaced). The repair can only be guaranteed if both the solder pads are intact (contact if unsure) however we can usually repair it even if the pads are damaged/missing. You don't need to send in the pieces that fell off the switch.
· Wire harness connector replacement ($15) - If your wire harness connector broke off, it will replaced with a brand new one for this price. This is also the cost for replacement of the connector if the pins are bent and can't be straightened out. Pictured below is a Virtue board, which is a common ailment.
· LED repair - see custom LED mod further down on the page.
· Eye ribbon connector reinstall ($10) - I can reattach the connector if it broke off your board (and you still have it).
Custom Modifications:
· Custom LED mod ($15) - This involves installing a new LED on the upper board that will shine out the back just like the stock blue one. Available colors are green, red, yellow, orange, white, or blue (stock). This is the perfect finishing touch to any color scheme.
· Flipped switch mod ($10) - Cost for flipping the trigger microswitch to the correct (flipped) position. If the switch is in the unflipped position then it won't work in the Shocker NXT frame. This is for the stock or any aftermarket board.
· Slikshot valve mod ($5) - This is required to use the NDZ Slikshot ram with the factory upgraded parts. Normally, you can't use the Slikshot ram with the factory upgraded valve poppet. The mod removes the spacer from the valve poppet and effectively turns it back to the stock poppet, allowing you to use it with the Slikshot ram. Performance is the same, however this mod can't be reversed once it's already been done.
· Membrane mod - no longer available.
