This page lists replacement screws for use with most SP markers, as well as some other markers. All screws are sold individually; none of the prices on this page is for anything other than one screw.
If you don't see what you need listed on this page, ask me for assistance. Chances are I have the screw you need and just haven't listed it on the site yet. If I don't carry the screw you need, I might start carrying it just because you asked for it.
Frame screw - $1/ea
Replacement frame screw for the Ion. Available in silver or black. This screw will work with all current Ion frames however it won't accomidate any bolt-on snatchgrips. | |
|
|
Breech screw - $1/ea
Replacement breech screw for the Ion breech/frame. Works with all current Ion frames and breech sections. | |
|
|
Grip panel screw - $0.75/ea
Replacement grip panel screws for any SP marker. This works with the stock frame, Punishers frame, and most others. Available in silver or black, in long length (stock grips) or short length (Hybrid grips). | |
|
|
Element Frame grip panel screw - $0.75/ea
This screw is used with the Element Ion frames. This screw is long so it will work only with thick grips (no hybrid). | |
|
|
Frame magnet screw - $1/ea
Replacement magnet / pre-travel stop set screw for Ion frames. | |
|
|
Regulator spring platform set screw - $0.75/ea
Replacement set screw for the side of the Ion stock vertical reg, that locks the spring platform in position. | |
|
|
Regulator endcap safety screw - $0.75/ea
Replacement set screw for the inside of the reg endcap (hidden within the oval hole in the reg housing), this prevents the endcap from being unscrewed too far. | |
|
|
Grip panel screw - $0.75/ea
Replacement grip panel screws for any SP marker. Available in silver or black, in long length (stock grips) or short length (Hybrid grips). | |
|
|
Vision eye screw - $0.75/ea
Replacement Vision eye ribbon screw, used on a Shocker SFT, Impulse, and Nerve. | |
|
|
Private Label frame, rear frame screw - $1/ea
Replacement rear frame screw for a Tonton, Warped Sportz Dark, 06 Dynasty, or Nerve frame. | |
|
|
Solenoid manifold screw - $1/ea
Replacement solenoid manifold screws; these screws hold the manifold to the Shocker body. Please note Nerves use different screws for their manifolds. | |
|
|
Solenoid spacer screw - $3/ea
This long screw holds the solenoid to the solenoid manifold. This will work with any 2004+ Shocker using the stock or NDZ manifold. It will work with the newer Evolve manifolds, but the older ones [that came with their own screws] are threaded differently.
Out of stock. | |
|
Out of stock
until further
notice |
Body set screw - $1/ea
These are the body set screws used to seal the internal air passages on a Shocker body (there are four of them total). Replacements are useful if you lose one or more screws for your gun and need to replace it/them.
These are high quality black oxide set screws. Regular steel or stainless screws won't work. | |
|
|
0.05" High-torque allen wrench - $2.50/ea
This is a special allen wrench that is slightly oversized so it will fit as snugly as possible inside hex screw heads. This allows for the most torque to be applied to the screw and helps to avoid stripping them out. I suggest using one of these if you plan on removing the body set screws from your Shocker body, to disassemble it for anodizing or thorough cleaning. These allen wrenches have an extra long shape to allow for maximum leverage. | |
|
|
Vertical adapter screw - $1/ea
Replacement vertical adapter screw for a Shocker or Nerve. This will function with all vertical adapters currently available, as well as any LPR vertical adapter. | |
|
|
Vertical adapter lock washer - $0.50/ea
This lock washer is required to space out the vertical adapter screw with the adapter itself. This is needed for all vertical adapters and LPR vertical adapters currently available. | |
|
|
Regulator set screw - $0.75/ea
Replacement set screw for the side of the Shocker and Nerve vertical Max-Flo. | |
|
|
Board/microswitch pin - $2.50/ea
Replacement pins that hold the board in place within the frame.
(These pins cost extra due to being more difficult to source than the powerswitch and vertical adapter ones...sorry).
Out of stock. | |
|
Out of stock
until further
notice |
Powerswitch actuator pin - $1/ea
Replacement magnetic pin that holds the transparent powerswitch actuator button inside the frame. | |
|
|
Vertical adapter pin - $1/ea
Replacement pin that prevents the vertical adapter from swiveling around. | |
|
|
Grip panel screw - $0.75/ea
Replacement grip panel screws for any SP marker. Available in silver or black, in long length (stock grips) or short length (Hybrid grips).
Please note that the silver screws accept a phillips-head screwdriver for removal, unlike the stock NXT screws which use a 1/16" allen wrench. | |
|
|
Eye cover screw - $1.10/ea
These screws are countersunk into the eye covers to hold them against the Shocker body. The screws available here are 1/16" longer than the stock ones, which helps to prevent stripping problems, and make reassembly (realignment of the eye cover) easier. Here is a picture of the screw installed. | |
|
|
Trigger rest retaining screw - $0.75/ea
This screw locks the trigger rest component in place within the frame. | |
|
|
Frame screw - $1/ea
Replacement frame screw used on a Shocker NXT. Available in silver only. | |
|
|
Solenoid manifold screw - $1/ea
Replacement solenoid manifold screws; these screws hold the manifold to the Shocker body. Please note Nerves use different screws for their manifolds. | |
|
|
Solenoid spacer screw - $3/ea
This long screw holds the solenoid to the solenoid manifold. This will work with any 2004+ Shocker using the stock or NDZ manifold. It will work with the newer Evolve manifolds, but the older ones [that came with their own screws] are threaded differently.
Out of stock. | |
|
Out of stock
until further
notice |
Body set screw - $1/ea
These are the body set screws used to seal the internal air passages on a Shocker body (there are four of them total). Replacements are useful if you lose one or more screws for your gun and need to replace it/them.
These are high quality black oxide set screws. Regular steel or stainless screws won't work. | |
|
|
0.05" High-torque allen wrench - $2.50/ea
This is a special allen wrench that is slightly oversized so it will fit as snugly as possible inside hex screw heads. This allows for the most torque to be applied to the screw and helps to avoid stripping them out. I suggest using one of these if you plan on removing the body set screws from your Shocker body, to disassemble it for anodizing or thorough cleaning. These allen wrenches have an extra long shape to allow for maximum leverage. | |
|
|
Vertical adapter screw - $1/ea
Replacement vertical adapter screw for a Shocker or Nerve. This will function with all vertical adapters currently available. | |
|
|
Regulator set screw - $0.75/ea
Replacement set screw for the side of the Shocker and Nerve vertical Max-Flo. | |
|
|
Regulator endcap safety screw - $0.75/ea
Replacement set screw for the inside of the reg endcap (hidden within the oval hole in the reg housing), this prevents the endcap from being unscrewed too far. | |
|
|
Dovetail set screw - $0.75/ea
Lock screw for the Shocker NXT frame's integrated dovetail rail. | |
|
|
Rear frame screw - $1/ea
Replacement rear frame screw for a stock Nerve frame. This will also work with a Shocker Tonton or Dark frame. | |
|
|
Grip panel screw - $0.75/ea
Replacement grip panel screws for any SP marker. Available in silver or black, in long length (stock grips) or short length (Hybrid grips). | |
|
|
Vision eye screw - $0.75/ea.
Replacement Vision eye ribbon screws, used on a Shocker SFT, Impulse, and Nerve. | |
|
|
Solenoid manifold screw - $0.75/ea
Replacement solenoid manifold screws; these screws hold the manifold to the Nerve body. Please note Shockers use different screws for their manifolds. | |
|
|
Solenoid spacer screw - $3/ea
This long screw holds the solenoid to the solenoid manifold. This will work on the Nerve stock solenoid manifold, or the NDZ stainless version.
Out of stock. | |
|
Out of stock
until further
notice |
Trigger rest plate screw - $0.75/ea
Replacement screw to hold the trigger rest plate within the frame. This is also used on a Shocker Tonton frame. | |
|
|
LPR lock screw - $1/ea.
Replacement tournament lock set screw for use with the Nerve and Mini-Flo LPR adjustment knob. Available in silver or black. | |
|
|
LPR bearing - $0.60/ea.
This metal bearing is placed between the LPR spring and piston (drop it into the LPR before reinstalling the spring/endcap). Its prupose is to help stabalize the LPR's output when adjusting it, by providing a buffer between the spring and piston. The bearing became a factory part on Nerves in early 2005 so any marker assembled prior to that likely never had this installed. | |
|
|
Vertical adapter screw - $1/ea
Replacement vertical adapter screw for a Shocker or Nerve. This will function with all vertical adapters currently available. | |
|
|
Vertical adapter lock washer - $0.50/ea
This lock washer is required to space out the vertical adapter screw with the adapter itself. This is needed for all vertical adapters currently available. | |
|
|
Regulator set screw - $0.75/ea
Replacement set screw for the side of the Shocker and Nerve vertical Max-Flo. | |
|
|
Board/microswitch pin - $2.50/ea
Replacement pins that hold the board in place within the frame.
(These pins cost extra due to being more difficult to source...sorry)
Out of stock. | |
|
Out of stock |
Powerswitch actuator pin - $1/ea
Replacement pin that holds the transparent powerswitch actuator button inside the frame. | |
|
|
Vertical adapter pin - $1/ea
Replacement pin that prevents the vertical adapter from swiveling around. | |
|
|
Grip panel screw - $0.75/ea
Replacement grip panel screws for any SP marker. Available in silver or black, in varied lengths. However, the length doesn't matter when installing these on an Impulse (sine there isn't any sensitive circuitry under the screw holes). | |
|
|
Frame screw - $1/ea
Replacement Impulse screw that holds the frame and circuit housing to the body. These screws have a larger head than the stock screws, to allow for a larger allen wrench hex; this larger head makes these screws virtually impossible to strip. Here is a picture of the screw installed on a marker. | |
|
|
Vision eye screw - $0.75/ea.
Replacement Vision eye ribbon screws, used on a Shocker SFT, Impulse, and Nerve. This will only work with the stock Impulse eye; this doesn't work with the Equalizer eye. | |
|
|
Frame mount screw - $0.75/ea
Replacement screws that hold the frame to the bottom of the circuit housing. | |
|
|
Mainboard screw - $1/ea
This screw holds the Impulse main circuit board in place within the circuit housing. | |
|
|
Regulator set screw - $0.75/ea
Replacement set screw for the side of the Impulse vertical Max-Flo reg. | |
|
|
